Alcohol Breathalysers

  • No ratings found yet!
0.00 Discount
Coupon Code: FREEBETA (Expiring in 2 months)
19Products found
View
Filter
  • iBlow10 Industrial Law-Enforcement Breathalyzer BASIC PACK

    iBlow10 is a high speed breathalyzer screener for testing drivers at road blocks and workers entering industrial sites.

     

    iBlow10 has a SuraCell Fuel Cell Sensor for ethanol specific alcohol testing which provides a long calibration cycle of 1 year.

     

    Digital Display of Test Results as well as GREEN or RED bright LED

    display based on a PASS or FAIL when any amount of alcohol is detected

    in breath OR based on a pre-set PASS / FAIL Limit depending on whether

    iBlow10 is ordered for Industrial Use or Law-Enforcement Use.

     

    iBlow10 provides 12 tests p/minute without the use of mouth pieces.

     

    iBlow10 offers Active and Passive testing for when drivers or workers have difficulty exhaling.

     

    LEDs for Night Time use with RED BLUE and BLUE ONLY options to direct drivers.

     

    Stock Available & Price includes VAT

    3,080.004,000.00
  • iBlow10 Industrial Law-Enforcement Breathalyser FULL PACK

    iBlow10 is a high speed breathalyser screener for testing drivers on the road & at road blocks & workers entering industrial sites.iBlow10 has a SuraCell Fuel Cell Sensor for ethanol specific alcohol testing which provides a long calibration cycle of 1 year. Digital Display of Results as well as GREEN or RED bright LED display based on a PASS or FAIL when any alcohol is detected in breath OR based on a pre-set PASS / FAIL Limit depending on whether iBlow10 is ordered for Industrial Use or Law-Enforcement Use.

    iBlow10 provides 12 tests per minute without the use of mouth pieces

    & offers Active and Passive testing for when drivers or workers have difficulty exhaling. LEDs for Night Time Use providing RED BLUE and BLUE ONLY options to direct drivers. Includes free downloadable PC software to download breathalyser test data from iBlow10 to a PC for analysis and record keeping.

    4,850.005,200.00
  • Alcoscan Interlock Breathalyser ALX1000

    Alcoscan ALX1000 is an Electrochemical Fuel Cell sensor based interlock breathalyser supplied with an ignition interlock for connecting to the ignition of a motor vehicle, bus or truck.

    After getting into the vehicle with the ALX1000 installed, the driver is required to blow into the breathalyser to be tested for alcohol. Depending on the result of analysis the ignition interlock will allow the vehicle to start or not.

    Alcoscan ALX1000 is suitable for trucks, busses, taxis and fleet managed vehicles to ensure that drivers do not drive while under the influence of alcohol.

    This system can be incorporated with the tracking systems for vans, busses and trucks.

    Annual calibration is recommended.


    Specifications


    Annual calibration is recommended.

    Category Contents
    Indication of B.A.C 0.00 to 0.40% B.A.C. or mg/l equivalent by LED display
    Accuracy +/-0.005%BAC at 0.100%BAC
    Mouth piece 5 full mouthpieces supplied with unit and additional mouthpieces available; 1 blow cup supplied with unit
    Sensor Fuel Cell type alcohol sensor
    Power supply Two 1.5V “AA” Alkaline batteries and power when connected to Interlock Device
    Weight 100g (Including batteries)
    Dimension (mm) 105 (height) X 50 (width) X 18
    Remarks Auto power off
    – Battery Low indication
    – CE, FDA approval
    – Air flow rate checking

    The Interlock device can be installed by an auto electrician and the pricing given does not include any installation costs.

    WE RECOMMEND THAT YOU ADD A PACK OF 100 MOUTHPIECES TO YOUR ONLINE SHOPPING CART WHEN ORDERING OR BUYING THIS PRODUCT

  • Alcoscan Entrance Breathalyser System EBS010 Sensor Modules

    AEntrance Breathalyser System (EBS010) Spare Sensor Modules for quick exchange and replacement of sensors on site without the requirement for immediately servicing and calibration.

    Saves times and means that EBS010 never has to leave your site when calibration of the sensor is required.

    Always order a spare sensor module when ordering an EBS010 so that you never have any down-time.


  • Alcoscan Entrance Breathalyser System EBS010 – INSTALLED

    Alcoscan EBS010 is a high speed automatic industrial breathalyser that is used to check the breath of workers for alcohol at Turn Stile gates and Entrances to sites, offices, mines, refineries and warehouses.

    Result outputs are provided by a 12V 1 sec pulse separate for Pass and Fail and by digital USB output in PC mode.

    If Dry Contact Relay OUTPUT for Pass and Fail is required an optional extra Relay Box is available.

    A Pass result allows access and a Fail result prevents access. Breath tests are ethanol specific and EBS010 performs over 600 tests per hour. Alcoscan EBS010 is built for Industrial and High Security environments.

    Annual calibration is recommended.

    This is the Installed Option.


    Specifications


    Annual calibration is recommended.

    Category Contents
    Indication of B.A.C 1) Pass is below 0.01% B.A.C. Fail can be set to fail from 0.01% B.A.C and up
    Accuracy +/-0.005%BAC at 0.100%BAC
    Mouth piece No Mouthpiece required
    Sensor Replaceable fuel cell type alcohol sensor
    Power supply 12VDC 1.5A power supply required – Supplied Standard
    Weight 550g
    Dimension (mm) 205 (height) X 108 (width) X 95
    Remarks – Auto power off
    – Air flow rate checking for no blows
    – Calibrated to fail from 0.01% B.A.C to prevent access at the lowest possible BrAC levels
    – Pricing excludes travel expenses to and from Sites
    – This pricing includes Installation in Series with a Turnstile Gate or Mag-Locking Gate and not full integration into a Time-Keeping System
  • Alcoscan Entrance Breathalyser System EBS010

    Alcoscan EBS010 is a high speed automatic industrial breathalyser that is used to check the breath of workers for alcohol at Turn Stile gates and Entrances to sites, offices, mines, refineries and warehouses.

    Result outputs are provided by a 12V 1 sec pulse separate for Pass and Fail and by digital USB output in PC mode.

    If Dry Contact Relay OUTPUT for Pass and Fail is required an optional extra Relay Box is available.

    A Pass result allows access and a Fail result prevents access. Breath tests are ethanol specific and EBS010 performs over 600 tests per hour. Alcoscan EBS010 is built for Industrial and High Security environments.

    Annual calibration is recommended.


    Specifications


    Annual calibration is recommended.

    Category Contents
    Indication of B.A.C 1) Pass is below 0.01% B.A.C. Fail can be set to fail from 0.01% B.A.C and up
    Accuracy +/-0.005%BAC at 0.100%BAC
    Mouth piece No Mouthpiece required
    Sensor Replaceable fuel cell type alcohol sensor
    Power supply 12VDC 1.5A power supply required – Supplied Standard
    Weight 550g
    Dimension (mm) 205 (height) X 108 (width) X 95
    Remarks Auto power off
    – Air flow rate checking for no blows
    – Calibrated to fail from 0.01% B.A.C to prevent access at the lowest possible BrAC levels
    – Pricing excludes installation costs
    – Time keeping and attendance technicians can easily install
  • Alcoscan ALP-1 incl Printer for Industry and Law-Enforcement BT

    Alcoscan ALP-1 BT is a fully portable IP54 rated water resistant Fuel Cell Sensor Industry and Law-Enforcement screener.

    ALP-1 meets the EN Standard – EN 15964:2011 for Breath alcohol test devices other than single use devices.

    This model includes a battery operated Mobile Folio Printer which prints results immediately upon breathalyser testing as well as captures and stores breathalyser results after each test for downloading and analysis.

    Alcoscan ALP-1 contains the latest 1-Inch full size Fuel Cell Sensor providing the highest accuracy available and ethanol specific results and a long calibration cycle.

    Provides both FAST no mouthpiece testing and NORMAL mouthpiece testing.

    Memory: Password protected last 500 test results with date and time of each test.

    This unit is suitable for Industrial and Law-Enforcement screening.

    Annual Calibration is recommended.


    Specifications


    Annual calibration is recommended.

    Category Contents
    Indication of B.A.C 0.000 to 4.000% or 0.000 to 0.400%BAC or 0.00 to 2.50 Mg/l BrAC by LCD display td>
    Accuracy +/-0.005%BAC at 0.100%BAC
    Mouth piece 5 full mouthpieces supplied with unit and additional mouthpieces available; 1 blow cup supplied with unit
    Sensor Full Size 1-Inch fully replaceable Electro-chemical Fuel Cell Sensor – Ethanol Specific
    Power supply Two 1.5V “AA” Alkaline batteries
    Weight 198g (Including batteries) – breathalyser only
    Dimension (mm) 133 (height) X 64 (width) X 33
    Remarks – Auto power off
    – Includes a Mobile Folio Printer, PC Software and Connector Cables.
    – Battery Low indication
    – Memory: Last 500 tests
    – Meets EN Standard – EN 15964:2011
    – Air flow rate checking in case of low breath volume
    – Annual Calibration Reminder
    – Certified Water resistant to IP54 rating IEC 60529:2001
    – PASS/FAIL Fast testing set to provide FAIL from 0.01% B.A.C

    WE RECOMMEND THAT YOU ADD A PACK OF 100 ALP-1 MOUTHPIECES TO YOUR ONLINE SHOPPING CART WHEN ORDERING OR BUYING THIS PRODUCT

  • Alcoscan ALP-1 incl Printer for Industry and Law-Enforcement

    Alcoscan ALP-1 is a fully portable IP54 rated water resistant Fuel Cell Sensor Industry and Law-Enforcement screener.

    ALP-1 meets the EN Standard – EN 15964:2011 for Breath alcohol test devices other than single use devices.

    This model includes a battery operated Mobile Folio Printer which prints results immediately upon breathalyser testing as well as captures and stores breathalyser results after each test for downloading and analysis.

    Alcoscan ALP-1 contains the latest 1-Inch full size Fuel Cell Sensor providing the highest accuracy available and ethanol specific results and a long calibration cycle.

    Provides both FAST no mouthpiece testing and NORMAL mouthpiece testing.

    Memory: Password protected last 500 test results with date and time of each test.

    This unit is suitable for Industrial and Law-Enforcement screening.

    Annual Calibration is recommended.


    Specifications


    Annual calibration is recommended.

    Category Contents
    Indication of B.A.C 0.000 to 4.000% or 0.000 to 0.400%BAC or 0.00 to 2.50 Mg/l BrAC by LCD display td>
    Accuracy +/-0.005%BAC at 0.100%BAC
    Mouth piece 5 full mouthpieces supplied with unit and additional mouthpieces available; 1 blow cup supplied with unit
    Sensor Full Size 1-Inch fully replaceable Electro-chemical Fuel Cell Sensor – Ethanol Specific
    Power supply Two 1.5V “AA” Alkaline batteries
    Weight 198g (Including batteries) – breathalyser only
    Dimension (mm) 133 (height) X 64 (width) X 33
    Remarks – Auto power off
    – Includes a Mobile Folio Printer, PC Software and Connector Cables.
    – Battery Low indication
    – Memory: Last 500 tests
    – Meets EN Standard – EN 15964:2011
    – Air flow rate checking in case of low breath volume
    – Annual Calibration Reminder
    – Certified Water resistant to IP54 rating IEC 60529:2001
    – PASS/FAIL Fast testing set to provide FAIL from 0.01% B.A.C

    WE RECOMMEND THAT YOU ADD A PACK OF 100 ALP-1 MOUTHPIECES TO YOUR ONLINE SHOPPING CART WHEN ORDERING OR BUYING THIS PRODUCT

  • Alcoscan ALP-1 for Industry and Law-Enforcement BT

    Alcoscan ALP-1 BT is a fully portable IP54 rated water resistant Fuel Cell Sensor breathalyser for Law-Enforcement and Industry alcohol screening.

    ALP-1 meets the EN Standard – EN 15964:2011 for Breath Alcohol test devices other than single use devices.

    ALP-1 captures and stores alcohol test results after each test which can be downloaded and analysed later on a PC.

    Alcoscan ALP-1 contains the latest 1-Inch full size Fuel Cell Sensor providing the highest accuracy available and ethanol specific results and providing for a long calibration cycle.

    Provides both FAST no mouthpiece testing and NORMAL mouthpiece testing.

    Memory: Password protected last 500 test results including date and time of each test.

    This unit is suitable for Industry and Law Enforcement screening.

    Annual Calibration is recommended.


    Specifications


    Annual calibration is recommended.

    Category Contents
    Indication of B.A.C 0.000 to 4.000% or 0.000 to 0.400%BAC or 0.00 to 2.50 Mg/l BrAC by LCD display td>
    Accuracy +/-0.005%BAC at 0.100%BAC
    Mouth piece 5 full mouthpieces supplied with unit and additional mouthpieces available; 1 blow cup supplied with unit
    Sensor Full Size 1-Inch fully replaceable Electro-chemical Fuel Cell Sensor – Ethanol Specific
    Power supply Two 1.5V “AA” Alkaline batteries
    Weight 198g (Including batteries) – breathalyser only
    Dimension (mm) 133 (height) X 64 (width) X 33
    Remarks Auto power off
    – Includes PC Software, USB Cable contained in a secure plastic carry case
    – Battery Low indication
    – Meets EN Standard – EN 15964:2011
    – Air flow rate checking in case of low breath volume
    – Annual Calibration Reminder
    – Certified Water resistant to IP54 rating IEC 60529:2001
    – PASS/FAIL Fast testing set to provide a Fail result from 0.01% B.A.C

    WE RECOMMEND THAT YOU ADD A PACK OF 100 ALP-1 MOUTHPIECES TO YOUR ONLINE SHOPPING CART WHEN ORDERING OR BUYING THIS PRODUCT

  • Alcoscan ALP-1 for Industry and Law-Enforcement

    Alcoscan ALP-1 is a fully portable IP54 rated water resistant Fuel Cell Sensor breathalyser for Law-Enforcement and Industry alcohol screening.ALP-1 meets the EN Standard – EN 15964:2011 for Breath Alcohol test devices other than single use devices.ALP-1 captures and stores alcohol test results after each test which can be downloaded and analysed later on a PC.Alcoscan ALP-1 contains the latest 1-Inch full size Fuel Cell Sensor providing the highest accuracy available and ethanol specific results and providing for a long calibration cycle.

    Provides both FAST no mouthpiece testing and NORMAL mouthpiece testing.
    Memory: Password protected last 500 test results including date and time of each test.

    This unit is suitable for Industry and Law Enforcement screening.

     

    Annual Calibration is recommended.


    Specifications


    Annual calibration is recommended.

    Category Contents
    Indication of B.A.C 0.000 to 4.000% or 0.000 to 0.400%BAC or 0.00 to 2.50 Mg/l BrAC by LCD display
    Accuracy +/-0.005%BAC at 0.100%BAC
    Mouth piece 5 full mouthpieces supplied with unit and additional mouthpieces available; 1 blow cup supplied with unit
    Sensor Full Size 1-Inch fully replaceable Electro-chemical Fuel Cell Sensor – Ethanol Specific
    Power supply Two 1.5V “AA” Alkaline batteries
    Weight 198g (Including batteries) – breathalyser only
    Dimension (mm) 133 (height) X 64 (width) X 33
    Remarks Auto power off
    – Includes PC Software, USB Cable contained in a secure plastic carry case
    – Battery Low indication
    – Meets EN Standard – EN 15964:2011
    – Air flow rate checking in case of low breath volume
    – Annual Calibration Reminder
    – Certified Water resistant to IP54 rating IEC 60529:2001
    – PASS/FAIL Fast testing set to provide a Fail result from 0.01% B.A.C

    WE RECOMMEND THAT YOU ADD A PACK OF 100 ALP-1 MOUTHPIECES TO YOUR ONLINE SHOPPING CART WHEN ORDERING OR BUYING THIS PRODUCT